| |
 |  |  |  |  |  |
 |
| |||||||
| MazdaSpeed 3/6 - ECU Computer Tuning Have an ECU tuning issue? Do you want to discuss Mazdaspeed 3/6 tuning solutions? Up to date info on the latest! Piasini Reflash, Cobb Access Port, Xede, Procede, Standback, Superchips & others supported here! |
 |
 | | LinkBack | Thread Tools | Display Modes |  |
 | 
07-02-2008, 04:50 PM
| #1 |  |
| Alittle Faster  Join Date: May 2008 Location: Cape Coral, FL
Posts: 807
My Mood:  iTrader: (1)
Rep Power: 307   
Thanks: 371
Thanked 601 Times in 125 Posts
Groans: 0
Groaned at 0 Times in 0 Posts
|  OBDII CONNECTORS Anyone try an OBDII "Y" connector to use 2 devices at the same time for readings? Can it be doable? OR will the readings be misread by two sources drawing power for the readings? Example: COBB AP and DashHawk  | ||||||||
|   |
|
07-02-2008, 06:43 PM
| #2 | |
| Senior Member  Join Date: Mar 2008
Posts: 136
iTrader: (0)
Rep Power: 19 
Thanks: 102
Thanked 21 Times in 14 Posts
Groans: 3
Groaned at 0 Times in 0 Posts
| Unfortunately, No. Something about them having the same address/code causes them to interfere with each other. Otherwise I would be rocking the dashhawk and AP Combo. | ||||||||
| |
|
07-02-2008, 07:01 PM
| #3 | |
| Alittle Faster Join Date: May 2008 Location: Cape Coral, FL
Posts: 807
My Mood: iTrader: (1)
Rep Power: 307
Thanks: 371
Thanked 601 Times in 125 Posts
Groans: 0
Groaned at 0 Times in 0 Posts
|
| |||||||||
|
| |
|
07-04-2008, 06:32 PM
| #4 | |
| Super Moderator  Join Date: Jun 2008
Posts: 222
My Mood:  iTrader: (0)
Rep Power: 15 Thanks: 27
Thanked 15 Times in 12 Posts
Groans: 13
Groaned at 2 Times in 2 Posts
| DashHawk Vehicle Information Display check out their tech forums.. there is a post stating the exact same thing.. | ||||||||
|
| |
|
07-04-2008, 08:51 PM
| #5 | |
| Alittle Faster Join Date: May 2008 Location: Cape Coral, FL
Posts: 807
My Mood: iTrader: (1)
Rep Power: 307
Thanks: 371
Thanked 601 Times in 125 Posts
Groans: 0
Groaned at 0 Times in 0 Posts
|
They don't say anything about the COBB AP, but they do say ID's conflicting with only two other types of scanners/readers on the OBDII port. I will try it with the COBB and see what happens. If that doesn't work, I will use the power mod for the DASHHAWK. Putting an on/off switch on line #1 of the DASHHAWK cable. Atleast that way I don't have to keep unplugging them to use either one.  Or a three way switch to power one or the other. | |||||||||
|
| |
|
07-10-2008, 03:27 PM
| #6 | |
| Alittle Faster Join Date: May 2008 Location: Cape Coral, FL
Posts: 807
My Mood: iTrader: (1)
Rep Power: 307
Thanks: 371
Thanked 601 Times in 125 Posts
Groans: 0
Groaned at 0 Times in 0 Posts
| FYI: Ok, tested the OBDII "Y" Cable with COBB AP and MSD DASHHAWK: DH overrides the AP connection no matter which one goes on first or the same time. AP will work if DH is unplugged or not in a reading state. If the DH is in menu, setup, etc then the AP will work. Other than that the DH has the primary control and AP is in an error or searching state. So making a pin #1 toggle switch in the DH cable will be needed or not depending how you want to do it. | ||||||||
|
| |
Linear Mode
